Beyond Construction

Register now

Forgot username?

Forgot password?

Remember Me
 
Home » Categories » Plumbing » Up Flush Systems » Saniflo

Saniflo – SANIPACK

 

 

 

Product Description

The Sanipack is a macerator device which is meant to be installed inside a wall cavity.  The Sanipack is a system that is used to install a complete bathroom up to 9 feet below the sewer line, or even up to 100 feet away from a soil stack.  It can handle the effluent from a toilet, sink and shower.

The Sanipack is simplicity itself to install; there are just four connections.

  • The macerator/pump is connected to the discharge pipe coming from a wall hung toilet
  • The toilet tank is connected to the water supply
  • The macerator/pump is connected to the small diameter discharge pipe work
  • The macerator/pump is connected to the electrical supply

The inside of the Sanipack is comprised of a pressure chamber, which starts and stops the unit, and the motor, which drives the stainless steel macerator blades and the pump.

  • When the flush is activated, the water flowing into the Sanipack activates a micro switch in the pressure chamber which in turn starts the motor.  The motor is sealed for life in an oil filled enclosure.  A common spindle/shaft drives the impeller and the macerator blades.  The moving parts therefore are kept to an absolute minimum.  Water and organic waste matter enter the chamber and are reduced to slurry as the macerator blades rotate at 3600 RPM.  The centrifugal force causes the reduced solids to be ejected through a grill into the container where it is picked up by the impeller pump mounted beneath the motor.
  • The unit pumps the effluent upward to 9 feet and/or 100 feet horizontally (with gravity fall).  Once the water is discharged and the water level in the container goes down, the micro switch deactivates the unit until the flush is activated again.  A normal operating cycle for Sanipack takes about 7-9 seconds depending upon the discharge pipe run configuration; power consumption is therefore minimal. 
  • In addition to the toilet waste, the Sanipack will also discharge gray water from a variety of other sanitary fixtures such as: a sink, a shower and a urinal.  When adding a shower, a base will have to be constructed.  This base should be made out of a 2" x 6" (minimum) or 2” x 8” (recommended) on edge, to allow for the installation of a P-trap and the required 1/4”per foot gravity flow towards the pump unit. 
  • The wastewater from other sanitary fixtures is discharged into the Sanipack via two 1-1/2 inch inlets on either side of the housing.  Either one or both inlets can be used as required.  The discharge elbow on top of the Sanipack can be turned either to the left, to the right, or towards the back, depending on the discharge installation.  A non-return valve, which comes already assembled on the discharge elbow, prevents back flow into the unit. 
  • This unit has been designed with a vent connection on the lid.  All plumbing codes require connection to a vent system.  Please note that the vent system should be a two-way air vent.  The use of mechanical vents, air admittance valves or similar devices are not permitted as these are considered one-way air vent systems.
  • It is also highly recommended for the macerator/pump to be connected to a Ground Fault Interrupter (GFI) circuit.
  • The Sanipack is designed to be used with a wall hung toilet.  The depth of the case allows for this pump to be installed within the wall.  Since the reservoir, the macerating pump and the pipes are hidden from view, this type of installation gives you the lean and clean look of a European bathroom.
  • The Sanipack has been certified to American and Canadian Standards.  Macerating standard; US: CSA Certified & IAPMO (UPC) listed - ASME A112.3.4, CA: Macerating Standard CSA B45.9.

Sanialarm

  • Our macerators and gray water pumps are designed for various types of applications. Therefore, they are exposed to different situations such as power failures, occasional abuse, or build-ups of limescale deposits in older units (if not regularly descaled) which can cause a surcharge of water in the unit.

SFA Saniflo introduces the Sanialarm!

  • The Sanialarm has a level pressure switch that triggers an alarm fixed on the top of the unit if the volume of water exceeds the maximum allowed level. The alarm emits a continuous 80 dB warning sound until it is switched off or the problem is rectified.
  • The Sanialarm is battery operated and can be installed on most models* in the Saniflo range, including Saniplus and Sanivite pumps.  It has been designed to be installed on new or existing Saniflo installations as it is quickly fitted onto the lid of the Saniflo unit.


* Suitable for use with Saniplus, Sanipro, Sanibest, Sanigrind, Sanipack and Sanivite.

Descaler

Regular descaling with specially formulated Saniflo descaler will prolong the unit's life and maintain optimum performance.  It is specifically created for use with Saniflo products and laboratory formulated with phosphoric acid.  Regular usage prolongs unit life, maintains efficiency and it is harmless to septic tank operation.

 

 

Specifications/ Literature

Illustrations and datasheet (PDF)

For additional information visit SANIPACK Product Page

 

 

 

Attachments Attachments
There are no attachments for this article.
Comments Comments
There are no comments for this article. Be the first to post a comment.
Related Articles RSS Feed
Saniflo – SANIBEST Pro
Viewed 420 times since Tue, Mar 26, 2013
Saniflo – SANIVITE
Viewed 402 times since Wed, Mar 27, 2013
Saniflo – SANICUBIC 1
Viewed 604 times since Tue, Mar 26, 2013
Saniflo – SANISHOWER
Viewed 414 times since Wed, Mar 27, 2013
Saniflo – SANITOP
Viewed 418 times since Wed, Mar 27, 2013
Saniflo – SANISWIFT
Viewed 393 times since Wed, Mar 27, 2013
Saniflo – SANICUBIC2
Viewed 347 times since Tue, Mar 26, 2013
Saniflo – SANIACCESS3
Viewed 433 times since Sat, Mar 23, 2013
Saniflo – SANICOMPACT
Viewed 329 times since Wed, Mar 27, 2013
Saniflo – SANIGRIND Pro
Viewed 418 times since Tue, Mar 26, 2013